← All Articles

Technical Proposals

Quality Plan in a Technical Proposal: What to Include

18 November 2026 · 7 min read · By NextBid Bid Experts

A quality plan scores when it shows who controls quality, what is inspected and how defects are closed on this contract. Here is what to include and how to avoid boilerplate.


A quality plan in a technical proposal is the section that shows how the quality of the work you are pricing will be controlled: who is responsible for quality, which procedures and inspections apply, how documents are controlled, and what happens when something does not conform. Written for the scope in the tender booklet, it gives the committee something specific to evaluate. Copied from a company manual, it adds pages and leaves the committee little to score.

This guide covers what the section contains, how to make it project-specific, and where ISO 9001 fits. It sits beside the work plan and schedule and the overall technical offer structure.

What does the booklet ask for in a quality plan?

The tender booklet (كراسة الشروط والمواصفات) decides whether a quality plan is a scored criterion, a sub-criterion of the methodology, or a document you attach. It also sets the criteria, the weights and the minimum technical score, and the committee applies what it states. Read the technical evaluation table and the scope of work before you write a line, and use the headings and order the booklet sets. If the booklet sets a limit on length or format, follow it.

Then list every quality requirement the booklet and its specifications contain (standards to be met, tests to be witnessed, certificates to be supplied, records to be handed over) in your compliance matrix, and point each row to the paragraph of the quality plan that answers it. The guide to reading a tender document shows how to read the booklet and its annexes for these requirements.

What should a quality plan contain?

ElementWhat to stateHow to make it project-specific
QA/QC organizationWho owns quality, who inspects, and to whom they reportName the roles for this contract and show them on the project organization chart
Quality proceduresThe procedures that control the main activities in the scopeList the activities from your own work breakdown, not a generic list
Inspection and test planWhat is inspected or tested, when, against which acceptance criteria, and who signsTake the tests and standards from the specifications in the booklet
Document controlHow drawings, submittals and records are issued, revised and archivedSay which documents the client approves before work proceeds
Non-conformance handlingHow a defect is recorded, contained, corrected and closedShow the route to the client's representative for this contract
Audits and reviewsInternal audits and review points during executionTie review points to your schedule milestones
Quality measures (KPIs)The measures you will record and reportChoose measures you already record, with the reporting interval
RecordsThe quality records handed to the clientMatch the handover list the booklet asks for

How do you present the QA/QC organization and the inspection plan?

State the reporting line first. A quality manager who reports outside the production chain shows that inspection does not depend on the people being inspected. Then name the roles for this contract: quality manager, site quality engineers or inspectors, and the person who coordinates with the client's supervisor. Use role titles that match the key personnel in your team CVs, so the organization chart and the CVs agree.

For the inspection and test plan, work from the specifications. For each major activity, show the inspection or test, the acceptance criterion and its source, the record produced, and the person who signs. Mark the points where work stops until the client's representative has inspected or approved (hold points) and the points where the client may attend (witness points). Do not invent tests the specifications do not call for, and do not leave out those they do.

How should non-conformances and audits be handled?

This part shows how well quality is controlled, so describe a closed loop in the order it happens:

  1. Identify and record the non-conformance on a numbered report.
  2. Contain it: stop or isolate the affected work so it is not covered up or built upon.
  3. Agree the disposition with the client's representative: rework, repair or reject.
  4. Find the cause and define the corrective action, so it does not repeat.
  5. Verify the correction by re-inspection and close the report.
  6. Report open and closed items to the client at the interval the contract sets.

Add your internal audit programme: what is audited (for example site activities against the procedures and records against the inspection plan), at what interval, and how findings are tracked to closure. Give an interval you will actually keep.

Does ISO 9001 matter, and which KPIs belong in the plan?

ISO 9001 is the international standard for quality management systems, and its requirements cover areas such as controlled documented information, internal audits and corrective action. Whether a certificate is required, or earns points, is for the booklet to say. If it asks for one, attach it as the booklet instructs. A certificate describes your company's management system. It does not describe how this project will be controlled, so the quality plan still has to.

For KPIs, pick a few that follow from the sections above and that you record in the normal course of work: for example inspection requests accepted at first inspection, non-conformance reports open beyond the agreed closing period, and audit findings closed on time. State how each is measured and reported. Do not publish targets you cannot support.

How do you keep it project-specific rather than boilerplate?

  • Use the contract's own activities, specifications and standards in every section.
  • Name the roles and the client interfaces for this project.
  • Refer to the booklet's records and handover requirements by name.
  • Align inspection points with the schedule milestones in your work plan.
  • Remove any paragraph that would read the same in a proposal for a different tender.

A quality plan scores when a committee can see who controls quality, what is inspected against which criteria, and how a defect is closed on this contract. Start from the booklet's requirements, then add the ISO 9001 reference and the company procedures.

Frequently asked questions

Is a quality plan mandatory in a Saudi government technical proposal?

It depends on the tender. The booklet states what the technical offer must contain and how it is scored, so check the evaluation criteria and the technical requirements. If the booklet asks for a quality plan or quality assurance methodology, answer it under the heading it uses.

Do I need an ISO 9001 certificate to bid?

Only if the booklet requires it or awards points for it. Check the qualification and technical requirements of the tender. Where it is required, attach the certificate as the booklet instructs.

What is the difference between QA and QC in a proposal?

Quality assurance covers the planned system: procedures, responsibilities and audits. Quality control covers checking the work itself through inspection and testing. A quality plan should address both for the scope of the tender.

Can I reuse my company quality manual as the quality plan?

Reuse the procedures it contains, but do not submit it as the plan. The plan has to apply them to this contract: its activities, specifications, roles, inspection points and records.

How long should the quality plan be?

The booklet sets any length or format limit, so follow it. Where it sets none, give each element enough detail to be checked against the specifications and no more.

Our bid management team writes technical proposals in Arabic and English, and our proposal design service lays out the organization charts, process flows and tables that make a quality plan easy to read and check against the booklet.

Related Insights

Explore more practical ideas to improve your bid win rate.

Technical Proposals

Facility Management Tender Proposal: What to Include

A facility management tender proposal turns the booklet's scope into a service matrix, a shift model, response times, a maintenance schedule and a mobilization plan. Here is what to show.

Read article →

Technical Proposals

Construction Tender Technical Proposal: What to Include

What a construction tender technical proposal contains: method statements, site organisation, equipment, manpower, schedule, quality and HSE plans, and subcontractors.

Read article →

Technical Proposals

Cybersecurity Tender Proposal in Saudi Arabia: NCA Guide

In cybersecurity tenders the technical offer is judged on NCA alignment, staffing, SOC location and measurable service levels. Here is how to write a proposal that shows each one clearly.

Read article →

Need support for your next bid?

Our team helps with bid writing, pricing strategy, and compliance review through final submission.

Book a Consultation